How To Pass Part E Of The Building Regulations
Posted in Soundproofing & Sound Testing on Nov 02, 2020
Soundproofing to ensure you meet the requirements of Part E of the Building Regulations should not be seen as an arduous task. Achieving good soundproofing between houses and flats is essential for our growing cities, nobody wants to hear their neighbours through a poorly soundproofed wall or hear the flat above you walking to and fro. Poor Sound Insulation is an issue that plagues many houses both small and large, through the development of noisy hobbies such as gaming systems, drum kits or food processors, or simply poorly soundproofed properties.
A lot of homeowners aren’t aware of the sound insulation requirements of Part E of the Building Regulations and further to this most won’t necessarily understand the importance of Sound Testing to show compliance with the regulations. Soundproofing to achieve compliance with Part E, should not be just about ‘Passing’ because if you ‘Just Pass’ or have a ‘Marginal Pass’ this means the property passes the required test but has poor soundproofing. This will have a knock-on effect for the owner renting the property for an extended period or the purchaser feeling they have purchased their dream home.
NOVA Acoustics Ltd deals with builders, architects, developers and specifiers on a day to day basis and the challenges behind soundproofing are very apparent. This series of articles aims to provide a baseline of knowledge for those suffering from a noise issue or designing or engineering a solution to a noise issue.
What is Approved Document E?
This document was last published in 2015 and deals with sound insulation. More specifically, it is concerned with the resistance within a property to the passage of sound. It gives advice on the requirements for sound insulation in both new dwellings and dwellings that have been converted from other types of building.
The scope of the document covers sound reduction between different rooms in residential terms as well as specific rooms in a dwelling. Acoustic conditions for common spaces in schools or flats are also covered too.
What specific areas is guidance given for in Approved Document E?
This document is made up of a total of 9 different sections. The areas they cover include:
Section 0: Performance
Section 1: Pre-completion testing
Section 2: Separating Walls and associated flanking constructions for new buildings
Section 3: Separating floors and associated flanking constructions for new buildings
Section 4: Dwelling-houses and flats formed by material change of use
Section 5: Internal walls and floors for new buildings
Section 6: Rooms for residential purposes
Section 7: Reverberation in the common internal parts of buildings containing flats or rooms for residential purposes
Section 8: Acoustic conditions in schools
There are also 5 annexes to the Approved Document as follows:
Annex A: Sets out the way of working out mass per unit area
Annex B: Advice on procedures around testing the installed sound installation
Annex C: Terminology
Annex D: Relevant references
Annex E: Important design detail
What are the key pieces of information contained?
All the above content covered is naturally essential but some may be more commonly referred to than others. The advice on pre-completion sound testing is most useful as it gives guidance on how to perform sound tests on properties as needed.
The sections on the separation of walls and floors comes in very handy also. These give various examples of the types of walls and floors you can use in new buildings along with any junction requirements. Section 4 is referred to when guidance is needed on work to existing areas within a property such as the walls or corridors. Many designers and engineers also find Section 5 most helpful as it provides advice on layout and junction requirements internally in a new property.
Soundproofing principles to help you pass Part of the Building Regulations
Below we look at the basics of soundproofing that will help you to achieve Part E of the Building Regulations.
We’ve all been in homes or flats where you can hear a person walking across the floor in the room directly above. This is particularly noticeable in buildings which have hardwood or marble floors and apartment buildings which have not been converted to a particularly high standard.
One of the best ways to reduce the sound of people walking on the floor above is to decouple the ceiling structure from the floor joists. This can be done using a Mute Clip System, a Resilient Bar System, A suspended MF Ceiling or an Independent Ceiling to decouple of the SoundBloc plasterboard linings from the joists above. Second to this decoupling the floor and creating a floating floor creates a suspension in the floor and decouples the cosmetic floor finish from the sub floor and minimise impact sound transference.
The same kind of system can also be used on the walls by creating a staggered or double stud wall which helps to reduce the spread of sound waves and vibration through the partition wall. Ideally, two layers of studwork should be installed with a good quality and high density acoustic mineral wool between the studs to reduce sound transmission even further.
Acoustic Mineral Wool
When soundproofing floors, to ensure your partition floor or wall achieves a good degree of sound insulation, you will need to install a good quality mineral wool between the joists or studwork. This needs to be tightly fitted between the framework to ensure a ‘snug’ fit and not have any gaps or voids. ALOT of soundproofing and building supplies companies will call any mineral wool ‘Acoustic Mineral Wool’ but to ensure you are getting the best product there is one simple rule. If it comes in a roll it is not acoustic! (Even if its got acoustic written on it!). We specify good quality Acoustic Slab Insulation, such as Rockwool RW45, Rockwool Flexi or Rockwool RW3. These mineral wool products come in varying slab sizes and whilst having a higher mass per cubic metre, improving the sound insulation, they are also easy to install and sit snuggly between you joists or studwork.
One of the key ways to improve the sound insulation of a party floor or wall is to ensure there is adequate mass, this can be done by using one of the higher mass mineral wool products mentioned above. There are also a number of Mass Loaded Vinyl products which can be used to apply to floors or walls. Finally, using SoundBloc, Duraline or SoundPlank ensures that your plasterboard linings also have the optimum mass. It is very challenging to achieve the requirements of Part E of the Building Regulations when using standard 12.5mm plasterboard on your ceiling.
For sound to travel through a wall, it actually has to move, hence the vibration. By making the walls heavy and a lot more rigid, they become harder to move, meaning the vibrations will be reduced. When soundproofing walls, some cost-effective choices for making walls heavier include plywood, OSB, and cement board. Though a heavy wall will still vibrate somewhat and you will still hear low frequencies, the sound will be reduced dramatically.
Air Tight Seal
One of the key areas to guarantee the sound insulation performance you are aiming for is by achieving an air tight seal. Air is like water, if there is any gaps, holes or cracks it will find a way through. Poor sealing is one of the most common reason for Sound Test Failures and is so easy to overcome. For example, with a timber floor construction take the following steps:
- Insulate between the joists with Rockwool RW45 and ensure this is tightly fitted between the timbers. Cut the insulation slightly proud of the joist spacing so that it holds itself in place.
- Ensure you leave an air cavity of 25 – 50% of the joist, this significantly improves the floors performance, never overfill with mineral wool and NEVER use Kingspan.
- On the underside of the ceiling, Install your ceiling system, Resilient Bars or Mute Clips. When installing your first layer of SoundBloc plasterboard affix this to the Resilient Bar or Furring Channel with no mechanical fixings (screws) to the joists. Finish the plasterboard with a 3mm gap around the perimeter. At this stage silicone the perimeter and joints. Now apply your second layer of SoundBloc plasterboard, stagger the joints, and follow the same process of finishing with a 3mm gap and silicone the perimeter and joints.
- From above apply your subfloor layer of 22mm Chipboard, if you are wanting a higher performing floor use a Cement Particle Board, this layer will need to be screwed into the joists. At this stage seal the perimeter and junctions within the room to ensure there are no gaps or holes.
- Finally lay your Composite rubber floor layer, Mutemat 2, over the top.
Finally adding damping to your wall and ceiling can help to dissipate the vibrations caused by sound waves. One of the easiest ways to add damping is to apply a layer of Tecsound between the plasterboard layers. Damping can be applied to all of the above soundproofing methods so long as two layers of board or drywall are being installed. When combined with a hot or resilient channel this results in a particularly effective soundproofing method.
NOVA Acoustics Ltd have a published a huge amount of Free Sound Insulation Design Advice here, including soundproofing floor and wall systems, as well as how to approach acoustic detailing and flanking sound. Click through to our Sound Insulation Design Advice section. Or if you need Sound Testing or Consultancy...Give us a Call to chat with one of our friendly consultants.